Skip to main content

Trio Kenwood KD-1033 turntable main bearing service

  One of my first posts in this blog was regarding the servicing of the Pioneer PL12D turntable, and that has proven to be the most popular by a significant margin. The Pioneer PL12D had its competitors, and probably the most popular alternative was the Trio Kenwood KD-1033 turntable. I use both names (Trio and Kenwood) as the company operated under different names in different markets. In the UK they were Trio, possibly because the brand Kenwood was most famous here for food blenders. 95% of a KD-1033 is similar to  Pioneer PL12D, and servicing them is very much the same process. Both are belt drive , have an AC synchronous motor,  mechanical speed change , a main bearing, sprung top deck and rubber motor mounts. the KD-1033 uses a different type of anti skate mechanism, employing a thread and weight. The plinth is shallower with an internal cross brace. One aspect that is different is the design of the main bearing, and servicing it is a little harder than a PL12D. The Pioneer main b

Repairing a Bosch microwave oven with a rusty door

I'm ashamed to say that recently I noticed rust developing at the base of the microwave interior glass door panel, and the paint flaking. Cooking items like potatoes releases a lot of moisture , which probably should be wiped away immediately to avoid this, but when you are preparing a meal and everything you forget (or I do at least). The Microwave is a Bosch and has a face plate so it fits into a recess in our fitted kitchen.



I looked into replacing the door but Bosch do not supply this as a spare, not could I find a donor oven online. A whole new oven would be around £300, which seemed a lot for a problem that might be fixable. 

I read online about Rusty Microwave ovens, and advice ranged from "It'll be fine" through to " immediately remove the oven and place in a lead lined container at the bottom of the sea" type of response. Filtering the informed advice from the hysterical took a while. In the USA you can purchase Microwave oven paint, and while I couldnt find  it in my local hardware shops, I did find an ebay seller selling a microwave touch-up kit consisting of a small tin of gloss black paint, emery paper , brushes and a stirrer for £10. Worth a go I reasoned

WARNING: Only attempt this if you are capable with electrical items and dismantling things in an orderly and careful fashion. If in doubt get a qualified repairer to undertake this


So first of all I removed and disconnected the microwave from its recess and from the electricity.

 I reasoned that working on the door would be much easier with it removed from the oven
 This necessitated removing the case from the oven, which was secured by screws along the back and sides. I placed all screws and removed hardware on a plastic tray so I didn't lose anything
This gave me access to the hinges which each had two bolts holding in place. Accessing the top bolts was easy from above, but the two lower bolts needed access through holes in the base. One of which is blocked by plastic trim which had to also be removed (two more screws)

 Below you see one of the bolts , which conveniently features a Phillips screw head too, via the access hole, the second bolt is blocked by the trim (top)




With the trim removed and the bolts undone (they were very stiff) I was able to remove the entire door


 Here you can see the rust and flaky paintwork

The inside window is surrounded by a plastic surround, which clips into place, and could be removed by gently easing a flat metal tool around the edge to disengage the internal clips. Gently does it,  and it came out without breaking anything .



Removing the plastic surround trim gave access to the window surround . I set about scraping off the loose paintwork using a knife


I reasoned that if the integrity of the door frame was sound i.e. the rust had not caused any structural damage i.e.  holes , it was safe to treat. If the door structure was compromised, then it would not provide a sufficient Microwave screen and would not be safe. I was relieved to find that the rust was surface only , not holes or severe damage to the underlying metal structure.



Once I had the paint scraped back I used a hobby drill with a wire brush attachment to remove as much rust as I could. 

NOTE TAKE GREAT CARE NOT TO SCRATCH THE WINDOW. IT FEATURES A PROTECTIVE METAL MESH WHICH PROTECTS THE EXTERIOR FROM THE MICROWAVE RADIATION.


Once I had the rust sanded back and I'd used a vacuum cleaner to remove the dust, I treated the rusted areas with an anti-rust treatment. It's basically an acid which reacts with the iron oxide and creates a good surface to paint.



 I let this dry, it changes the rust frst to a blue colour then to black.


Once dried over night, I painted the rusted section, with two coats of the  Microwave paint, each coat allowing 24 hours to dry

Here you can see completely reassembled, reversing the sequence above and back to normal.
A repaired rusted door . While the paint finish internally is not as smooth as original, it is sound and not visible externally. Good enough and cheaper than a new oven. Job done



Comments

Popular posts from this blog

Restoring a Pioneer PL-12D Turntable

 I got back into vinyl records about 18 months ago, and have collected a few hundred albums, mostly second hand. I have a number of turntables (NAD 5120, Ariston QDeck, Pioneer PL12D ) which I got also second hand. I keep a few, some end up passed onto friends, some that are too far gone are kept for spares. In most cases they have required a little work to get them running again. Last week I was lucky enough to get a Pioneer PL-12D turntable from freecycle. The lady who offered it, said that she in turn had received it from freecycle , and had replaced the belt but couldn't get on with the springiness of it, and had got a modern USB turntable. I have previously worked on one of these decks, and know what she means about the suspension system used. While this blog is specifically about this particular model of deck, many of the concepts are similar to others from this vintage. Many Japanese belt drive decks throughout the  1970's shared very similar construction, so this ma

Bracing IKEA EXPEDIT or KALLAX cabinets for greater rigidity when used with a turntable

The inevitable problem, too many records. Turntable and amplifier on top Like many record collectors around the world, I have a number of IKEA cube cabinets from both their EXPEDIT (older) and KALLAX (newer) ranges. These are easy to make, cheap to buy and perfect for record storage. The system comes flat packed and uses bolts and dowels to hold the system together. If you follow the instructions  the system is strong and should not collapse. You can augment the joints with PVA wood glue for extra strength. My turntable sits on top of an EXPEDIT 2x4 cabinet, laid along the long side, with some felt feet to support it from the floor, and you can use KALLAX in the same way. It's been great but has two problems I wanted to address : 1) Because the system has no back panel, the records  can be pushed too far back. 2) While the structure is strong and fairly rigid, there was some lateral movement. With heavy equipment on top, I found that if I nudged or knocked either top side, this all

Replacing MR16 Halogen bulbs with LED equivalents

If you have read my other blogs about GU10 mains voltage halogen lighting, you will know that I have mostly replaced these bulbs with LED equivalents. they cost more, but last longer, are cooler and use a fraction of the energy. a halogen bulb is typically either 35 or 50 watts. most LED bulbs are 3 watts. While the bulbs in my house are predominantly GU10 mains halogens, I do have a couple of MR16 bulbs. These are a different type of halogen that operate from a 12volt supply. I should mention at this point that I don't have any dimmer switches in my house. Now some mains voltage GU10 LED bulbs are dimable (always check first). MR16 bulbs have two pin connectors rather than the lugs found on GU10 bulbs. GU10's use a push and twist method of connecting to the socket. the MR16 simply push in place with metal clips also gripping the edge of the bin base. They use a separate power supply , either a transformer (old type ) or a switch mode power supply(newer) to convert 250v